Quick answer: Choose 1.85 mm connectors for precision work up to 67 GHz, 2.92 mm (K-type) for 40 GHz general microwave, and 1.0 mm for 110 GHz mmWave and VNA measurements. All three are 50 Ω, threaded, and mechanically incompatible with each other — you must match interfaces or use an adapter. INERGEK manufactures all three families as connectors, adapters and phase-stable cable assemblies, with published specs for every SKU.

RF engineers searching for "1.85 mm connector", "1.0 mm connector" or "1.8 mm connectors" are usually trying to resolve one question: which precision interface covers their frequency band without wasting budget or introducing a mismatch. This guide answers that directly, with the numbers that matter — frequency ceiling, mating interface, impedance, power handling and repeatability — so you can specify the right part the first time.

What is the difference between 1.85 mm, 2.92 mm and 1.0 mm connectors?

The number is the inner diameter of the connector's outer conductor, in millimetres. A smaller interface supports a higher maximum frequency because it keeps the coaxial mode below cutoff. The trade-off is mechanical: smaller interfaces are more delicate, cost more, and demand tighter torque control.

Quick comparison — frequency, interface, impedance, best use, limitation

InterfaceMax frequencyCouplingImpedanceBest forKey limitation
1.85 mm (V)DC–67 GHzThreaded, precision50 ΩmmWave test, 5G/6G, radar, VNA portsDelicate; needs torque control
2.92 mm (K)DC–40 GHzThreaded, mates with SMA footprint50 ΩGeneral microwave, 40 GHz modulesNot fully interchangeable with SMA at 40 GHz
1.0 mm (W)DC–110 GHzThreaded, ultra-small50 Ω110 GHz measurement, on-wafer, R&DFragile; highest cost; dedicated adapters
SMA (reference)DC–18 GHz (26.5 GHz precision)Threaded50 ΩEveryday RF up to 18 GHzFrequency ceiling well below mmWave

How do I choose by frequency band?

  • Below 18 GHz: standard SMA is the cost-effective default; no need to pay for a precision mmWave interface.
  • 18–40 GHz: 2.92 mm is the workhorse. It keeps an SMA-compatible mating footprint while extending the ceiling to 40 GHz.
  • 40–67 GHz: move to 1.85 mm. This is the sweet spot for 5G/6G front-ends, automotive radar and VNA test sets where 2.92 mm runs out of bandwidth.
  • Above 67 GHz to 110 GHz: 1.0 mm is the only practical coaxial choice for on-wafer probing and 110 GHz measurement systems.

INERGEK stocks the full chain — browse the 1.85 mm connector category, the 2.92 mm category, and ready-made 1.85 mm to 2.92 mm adapters when a mixed-interface lab setup is unavoidable.

Can 1.85 mm and 2.92 mm connectors mate with each other?

No. Although both are 50 Ω and threaded, their outer-conductor diameters differ (1.85 mm vs 2.92 mm), so they cannot be physically mated without an adapter. Forcing a mismatched pair damages the precision interface and ruins return loss. Plan your bill of materials around a single interface per signal path, and use a rated adapter only at the boundary. INERGEK offers precision in-series adapters such as the 1.85 mm male to 1.0 mm male adapter for exactly this purpose.

Why does impedance and PIM matter at mmWave frequencies?

At 40–110 GHz, a tiny impedance discontinuity produces a measurable reflection. Precision interfaces hold 50 Ω with tight tolerance and use air dielectric to keep insertion loss low and phase stable across temperature. In base-station and antenna feeds, passive intermodulation (PIM) is equally critical — a poor joint generates spurious signals that desensitise receivers. For low-PIM outdoor installations, pair precision connectors with sealed (IP67) bodies and verified torque. INERGEK supplies per-unit test data on request for mmWave cable assemblies.

Frequently asked questions

What does the number in 1.85 mm or 2.92 mm actually mean?

The number is the nominal inner diameter of the connector's outer conductor, measured in millimetres. A 1.85 mm interface has a 1.85 mm outer-conductor bore, a 2.92 mm interface has a 2.92 mm bore, and a 1.0 mm interface has a 1.0 mm bore. This dimension sets the upper frequency limit: a smaller bore pushes the unwanted higher-order coaxial mode further out, so the connector can operate at a higher frequency. It also makes the mating interface more delicate and more expensive to machine to tolerance.

Is 2.92 mm the same as SMA?

No. A 2.92 mm (K-type) connector has the same mating-thread footprint as SMA, so it can physically screw onto many SMA parts, but it is rated to 40 GHz while standard SMA stops around 18 GHz. Using a 2.92 mm interface in a 40 GHz signal path is correct; assuming an SMA component will perform to 40 GHz just because it fits is not. For repeatable 40 GHz measurements, keep the whole path — cable, adapters and device — in 2.92 mm and use connectors with documented return-loss data.

Which connector should I choose for a 67 GHz application?

Choose a 1.85 mm interface. It is specified from DC to 67 GHz, which covers the full 5G mid-band and most mmWave R&D, radar and test applications in that range. A 2.92 mm connector tops out at 40 GHz and will not work at 67 GHz, while a 1.0 mm connector would work but is more fragile and costly than necessary. For a 67 GHz setup, use 1.85 mm connectors and phase-stable cable assemblies, and control mating torque to protect the precision interface over repeated cycles.

When is 1.0 mm connector necessary?

A 1.0 mm interface is necessary when your operating frequency exceeds 67 GHz and reaches up to 110 GHz — for example on-wafer probing, 110 GHz VNA measurements and advanced semiconductor characterisation. It is the smallest standard coaxial interface and the most delicate, so it is reserved for controlled lab environments rather than field cabling. If your highest frequency is 67 GHz or below, a 1.85 mm connector is the more robust and economical choice. INERGEK stocks 1.0 mm connectors and 1.85 mm to 1.0 mm adapters for mixed-frequency test benches.

Need help selecting a millimeter-wave interface for your frequency band? INERGEK engineers publish full specifications — frequency range, VSWR, impedance and mating cycles — for every SKU, and provide fast quotes for custom cable assemblies. Explore the RF & microwave catalog or contact our team for a datasheet.